Journal Coil
Rebuildables

Geekvape box mod for rebuildables, what the spec sheets say

Written by Sarah Meunier · · 9 min. read

Geekvape box mod for rebuildables, what the spec sheets say
Picture: Guillaume Bleyer / Unsplash

Fitting a rebuildable atomiser to a Geekvape box mod looks easy. The real sorting happens elsewhere, in a handful of spec sheet lines that retail listings rarely copy across. Which temperature control modes does the mod declare? How high a resistance will it fire, and what current will it pull from a very low build? The journal went back to the official spec sheets of five Aegis mods with six builder’s criteria, the modes, the power, the resistance range, the current, the voltage and the power source.

Which Geekvape box mod for a rebuildable atomiser

For a builder who wants every mode, the T200 and the Legend 5 are the only two Geekvape box mod models, among the five spec sheets checked, that declare temperature control by wire type. Both accept 0.1 to 2 ohms, with a maximum of 45 A of current and 12 V of voltage.

The Solo 3 keeps a TCR mode and goes up to 3 ohms, which makes it more flexible for a mouth-to-lung build. The newer Solo 5 and Mini 5 declare only two modes, Smart and Power. In Power mode, they heat a kanthal or nichrome wire at a set wattage, and no more.

Five mods, six builder’s criteria

The table uses the figures published by the official Geekvape store and the manufacturer’s website. “Not published” marks data missing from the spec sheet, not a feature missing from the mod.

ModDeclared modesPowerResistance rangeMax currentMax voltagePower source
Legend 5Eco, Smart, Normal, Custom, TC5 to 200 W0.1 to 2 ohms45 A12 V2 x 18650 cells, not included
T200Power, TC-SS, TC-TCR, VPC, Smart, Bypass5 to 200 W0.1 to 2 ohms45 A12 V2 x 18650 cells
Solo 3Smart, Power, Boosting, Memory, Eco, TCR5 to 100 W0.1 to 3 ohms32 A7.5 V1 x 18650 cell or 3000 mAh battery
Solo 5Smart, Power5 to 100 Wnot published30 Anot published1 x 18650 or 21700 cell, adapter included
Mini 5two modes, resistance detection5 to 100 Wnot publishednot publishednot publishedbuilt-in 3200 mAh battery

The Solo 5 row needs a word of explanation. Its kit page shows a range of 0.1 to 0.2 ohm, a figure that is plainly cut short, and the page for the mod alone gives none at all. The journal therefore leaves it out.

Temperature control, what each Geekvape box mod declares

Temperature control does not set a wattage but a heating ceiling. It only works with a wire whose resistance changes clearly as it heats, such as stainless steel, nickel or titanium. Kanthal, too stable, is ruled out. This is the criterion that splits the range most sharply.

Legend 5 and T200, full TC

On the Legend 5, the spec sheet lists a TC mode, and the review published by the official store states that it works with stainless steel, nickel and titanium wire. The builder then sets a temperature rather than a number of watts.

The T200 splits it in two. TC-SS targets stainless steel, while TC-TCR lets the builder enter a wire’s temperature coefficient, which opens the door to alloys with no preset. It adds a Bypass mode and a VPC power curve, two settings missing from the other spec sheets.

Solo 3, TCR on its own

The Solo 3 lists six modes, one of them TCR. No preset stainless steel or nickel mode appears. To use it, you need to know your wire’s coefficient before the first fire.

Solo 5 and Mini 5, two modes and nothing more

The Solo 5 advertises a “Dual Mode”, Smart and Power. The Mini 5 uses the same wording, with its page mentioning “smart” temperature management without naming any TC mode. Geekvape’s own comparison sets the Solo 5 against the Solo 3, and the newer mod drops the TCR mode of its predecessor.

Resistance range and electrical limits on a Geekvape box mod

Two ceilings frame a home-made build on a Geekvape box mod. At low values, maximum current caps the power. At high values, maximum voltage does. Both come from Ohm’s law, set out in our article on Ohm’s law and battery safety with rebuildables.

At low resistance, current decides

Power equals the square of the current multiplied by the resistance. With 45 A at 0.1 ohm, the Legend 5 and the T200 can reach 202.5 W, so their 200 W remain available at the bottom of their range. The Solo 3, with 32 A, reaches 102.4 W at 0.1 ohm.

The Solo 5 is the only one to hit a wall before its rated power. With 30 A, its 100 W are only reached from about 0.111 ohm upwards. A parallel build at 0.1 ohm would top out at around 90 W, if the mod accepts that value, which its spec sheet does not make clear.

Above 1 ohm, voltage decides

Power also equals the square of the voltage divided by the resistance. With 12 V at 2 ohms, the Legend 5 and the T200 deliver 72 W at most, far beyond what a mouth-to-lung build asks for.

Their real limit lies elsewhere. A 2.4 ohm build falls outside their declared range. The Solo 3 accepts it, with 7.5 V at most, which gives 28.1 W at 2 ohms and 18.75 W at 3 ohms. A build below the floor generally triggers a protection message instead, of the kind covered in our piece on the short atomizer error.

Fitting an RTA or RDA to an Aegis mod

Once the mod is chosen, three hardware points still need checking before the first build. None appears in the power tables, yet all of them can be read on the spec sheet or on the atomiser.

Cells with flat ends

The Legend 5 spec sheet asks for two 18650 cells with flat surfaces at both ends, or the battery door will not close. The Solo 3 sheet sets the same condition for its cell. A cell’s current rating matters too. With two cells in series, each one supplies the power divided by the pack voltage, around 27 A at 200 W on a nominal 7.4 V, and more as the cells run down. The mod’s 45 A maximum is measured at the coil.

A width to compare with the diameter

Geekvape publishes no maximum atomiser diameter. The face widths give a rough guide, 56 mm for the Legend 5, 56.05 mm for the T200, 42.55 mm for the Solo 5 and 40.94 mm for the Solo 3. A wide dripper is therefore worth measuring against these figures before buying.

A 2 ml tank in the UK

UK rules cap refillable tanks at 2 ml and nicotine e-liquid at 20 mg/ml, sold in bottles of no more than 10 ml. The Legend 5 kit comes with a 5.5 ml glass or a 2 ml TPD glass, and the 2 ml version is the one for the UK market, as it is for an RTA. A dripper with no tank sidesteps the question, as our article on RDA, RTA and RDTA explained shows.

Which builder for which mod

The criteria do not weigh the same depending on how you build. The verdict follows four profiles, from the most demanding to the simplest.

  • Temperature control builder, the T200, the only one combining TC-SS, TC-TCR and Bypass, then the Legend 5 and its stainless steel, nickel and titanium TC.
  • Low resistance dripper, the Legend 5 or the T200, whose 45 A are enough for 200 W at the 0.1 ohm floor.
  • Mouth-to-lung build above 2 ohms, the Solo 3, the only one going up to 3 ohms.
  • Occasional kanthal build at a set wattage, the Solo 5 or the Mini 5 are enough, in Power mode.

No single mod covers every profile. On modes alone, the T200 declares the most for a hand-made wire, with the same electrical ceilings as the Legend 5.

FAQ

Five answers to the questions that come up in searches on the range.

What is the Geekvape Aegis box mod?

Aegis is the name of Geekvape’s rugged range, not of a single model. The spec sheets give an IP68 rating to the Legend 5, Solo 5, Solo 3 and T200, and an IP67 rating to the Mini 5.

What is the latest Geekvape box mod?

In the official store catalogue, the fifth generation groups the Legend 5, the Solo 5 and the Mini 5. The manufacturer’s page for the Legend 5 is dated June 2025.

Built-in battery or removable cells, which to choose?

Removable cells can be swapped and charged separately, whereas a built-in battery charges inside the mod. The Mini 5 carries 3200 mAh and accepts 5 V and 3 A charging, while the Solo 3 exists in both versions.

Where can I find Geekvape spare parts?

Geekvape puts a spare parts pack and a second glass in the Legend 5 kit. The official store also sells glass on its own, and retailers generally stock the same parts.

Does Smart mode suit a home-made build?

Geekvape describes this mode as coil detection followed by automatic wattage optimisation. The spec sheet does not say what that calculation rests on. For a hand-made build, Power mode set from your own calculation is easier to read.

Geekvape box mod and rebuildables, the key points

Read from the workbench, the range splits in two. The T200 and the Legend 5 declare temperature control by wire, 45 A and 12 V, over a range of 0.1 to 2 ohms. The Solo 3 keeps TCR and goes up to 3 ohms, while the Solo 5 and the Mini 5 make do with two modes.

Before fitting an atomiser, three checks remain, flat-ended cells, a face width to compare with the diameter and a 2 ml tank. Choosing a Geekvape box mod for a rebuildable therefore means reading its spec sheet the way you read a build, value by value, a habit that works for any regulated mod.

Editorial content for adult readers only. Vaping products can contain nicotine, which is a highly addictive substance. Vaping products are not for sale to anyone under 18 in the UK. This article is not a buying recommendation.